PIC18F2520-I/ML【PDF 53/151 页】IC PIC MCU FLASH 16KX16 28QFN

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3832

49页 50页 51页 52页 [53页]54页 55页 56页 57页

PIC16(L)F1782/3

DS41579C-page 320

Preliminary

2011-2012 Microchip Technology Inc.

27.1.1.5

TSR Status

The TRMT bit of the TXSTA register indicates the

status of the TSR register. This is a read-only bit. The

TRMT bit is set when the TSR register is empty and is

cleared when a character is transferred to the TSR

until all bits have been shifted out of the TSR register.

No interrupt logic is tied to this bit, so the user has to

poll this bit to determine the TSR status.

27.1.1.6

Transmitting 9-Bit Characters

The EUSART supports 9-bit character transmissions.

When the TX9 bit of the TXSTA register is set, the

EUSART will shift 9 bits out for each character transmit-

ted. The TX9D bit of the TXSTA register is the ninth,

and Most Significant, data bit. When transmitting 9-bit

data, the TX9D data bit must be written before writing

the 8 Least Significant bits into the TXREG. All nine bits

of data will be transferred to the TSR shift register

immediately after the TXREG is written.

A special 9-bit Address mode is available for use with

multiple receivers. See Section 27.1.2.7 “Address

Detection”

for more information on the address mode.

27.1.1.7

Asynchronous Transmission Set-up:

Initialize the SPBRGH, SPBRGL register pair and

the BRGH and BRG16 bits to achieve the desired

baud rate (see Section 27.4 “EUSART Baud

Rate Generator (BRG)”

Enable the asynchronous serial port by clearing

the SYNC bit and setting the SPEN bit.

If 9-bit transmission is desired, set the TX9 con-

trol bit. A set ninth data bit will indicate that the 8

Least Significant data bits are an address when

the receiver is set for address detection.

Set SCKP bit if inverted transmit is desired.

Enable the transmission by setting the TXEN

control bit. This will cause the TXIF interrupt bit

to be set.

If interrupts are desired, set the TXIE interrupt

enable bit of the PIE1 register. An interrupt will

occur immediately provided that the GIE and

PEIE bits of the INTCON register are also set.

If 9-bit transmission is selected, the ninth bit

should be loaded into the TX9D data bit.

Load 8-bit data into the TXREG register. This

will start the transmission.

FIGURE 27-3:

ASYNCHRONOUS TRANSMISSION

Note:

The TSR register is not mapped in data

memory, so it is not available to the user.

Word 1

Stop bit

Word 1

Transmit Shift Reg.

Start bit

bit 0

bit 1

bit 7/8

Write to TXREG

Word 1

BRG Output

(Shift Clock)

TX/CK

TXIF bit

(Transmit Buffer

Reg. Empty Flag)

TRMT bit

(Transmit Shift

Reg. Empty Flag)

1 TCY

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式